2001 Cadillac Deville Dts on 2040-cars

Auto blog

2016 Cadillac ATS-V First Drive [w/video]

If you get hot and bothered for hot-rodded sedans and coupes, you probably know that Germans have long dominated that cutthroat scene. For years, the Audi RS/BMW M/Mercedes-AMG triumvirate has ruled the microcosm of grunty, mid-level luxury cars. But a funny thing happened when Cadillac's first V car hit the market in 2004. Since the CTS-V crashed the high horsepower party, German tuning houses started thinking less about the "Daddy's Caddy" stereotypes and more about the next imminent threat – in this case, the inevitable high-horsepower spinoff of the smaller, nimbler Cadillac ATS. The standard ATS' defense against the German triad hasn't been triumphant so far (GM's Michigan plant was idled for three weeks in 2014 due to excess inventory), but the souped-up 2016 Cadillac ATS-V presents a fresh bid to put the Teutonic competition on alert. The ATS-V's flared bodywork and quad exhaust pipes offer bits of visual shock and awe, but significant hardware upgrades back up the go-fast looks. Front and center is a twin-turbocharged, 3.6-liter V6 with reworked internals including a charge-air cooler, titanium connecting rods, and titanium-aluminide turbines. The new engine produces 464 horsepower and 445 pound-feet of torque, up a staggering 262 hp and 173 lb-ft compared to a base, four-cylinder ATS. Those output figures eclipse the BMW M3/M4 (425 hp, 406 lb-ft) and Audi RS5 (450 hp, 317 lb-ft), but lag slightly behind the V8-powered Mercedes-AMG C63 (476 hp, 479 lb-ft), and more so the C63 S (503 hp, 516 lb-ft). The chassis benefits from several structural braces, most notably a shear panel intended to boost front-end stiffness. Extra poundage from the add-ons are minimized through lighter-weight materials – in the case of the shear panel, stamped aluminum. Cadillac says though it intended to make the ATS the quickest car in its segment (stated 0-60 mph times between 3.8 and 3.9 second virtually match the BMW M4 and Mercedes-AMG C63 S' 3.9 figure), the development team says they also focused on subjective qualities like turn-in quickness and steering response. As such, toe links have been replaced with ball joints, mounts have been retuned, and reworked magnetic damping offer greater responsiveness. Six suspension bushings have been stiffened and ten have been completely redesigned, and the Performance Traction Management system that tames beasts like the Corvette Z06 and Camaro ZL1 also helps lay down power in the ATS-V.

Cadillac to recall 20,000 SRX models over wheels that could fall off

A potential issue with the lug nuts on 19,871 units of the 2013 Cadillac SRX in the US and Canada has lead to a recall of the luxury crossover. Those lug nuts that have a Teflon topcoat, identified by their bluish tint, could loosen and cause "creaking, rattling or grinding noises or steering vibrations." In the worst case scenario, a wheel could fall off, but there have been no reports of that happening, nor any reports of accidents or injuries due to the issue.
This is the second recall action on the SRX over the last few months. In March, Cadillac recalled 27,000 SRX models over a transmission programming issue. General Motors will begin notifying customers with the potentially faulty parts on June 3, at which time they can take their vehicles to dealers to have the tires rotated and new nuts installed. A further 7,397 SRXs exported from North America also face the recall action.

GM adds 1,200 jobs at Detroit-Hamtramck plant

General Motors is making a big move at its Hamtramck, MI, factory, announcing it will add a second shift and hire over 1,200 workers within the next several months. It's expected that by early 2016, the factory will employ over 2,800 workers to build the Chevrolet Volt, Impala, Malibu, Cadillac ELR, and by early next year, the new CT6. According to GM Hamtramck spokesperson Courtney Zemke, 40 of the 1,200 positions are for salaried employees, while the remainder will be hourly positions. As for where these employees will go, positions are being made available across the factory, so GM isn't focusing on any particular area for its new hires. It's a similar story behind the hiring surge itself. GM said in its press release that the "second shift is necessary to meet forecasted market demand," a position Zemke reiterated. It's a matter of demand across the plant's portfolio, rather than any one particular product seriously outstripping supply. Naturally, the United Auto Workers is happy with the move. "The workforce at Detroit-Hamtramck is second to none," UAW Local 22 Shop Chairman Don LaForest said in the attached release. "We appreciate the opportunity to expand our UAW-GM family." Hiring is going on now, with the second shift slated to get underway in early 2016. GM's Detroit-Hamtramck Assembly to Add Second Shift and More Than 1,200 Jobs Plant will nearly double its workforce by early 2016 2015-10-22 DETROIT – General Motors is nearly doubling its workforce at Detroit-Hamtramck Assembly by adding a second shift and more than 1,200 hourly and salaried jobs. The addition of a second shift will increase the plant's workforce to approximately 2,800 people when hiring is completed. The second shift is necessary to meet forecasted market demand for the five cars produced at Detroit-Hamtramck. "This is the result of the award-winning vehicles Detroit-Hamtramck produces and the confidence GM has in our team to build world-class quality for our customers," said Plant Manager Gary West. Second shift hiring is underway, and the shift is scheduled to begin operations in early 2016. "The workforce at Detroit-Hamtramck is second to none," said UAW Local 22 Shop Chairman Don LaForest. "We appreciate the opportunity to expand our UAW-GM family." The 4.1 million-square-foot Detroit-Hamtramck Assembly opened in 1985. GM has invested $1 billion in the plant over the last six years, making it one of the company's most-agile manufacturing facilities in North America.