2004 Audi S4 Red/white 6speed Low Miles Carfax Certified on 2040-cars

Auto blog

Audi Sport Quattro Concept to race into Frankfurt

Audi has pulled the official wraps off its new Sport Quattro Concept, which will be debuted at the 2013 Frankfurt Motor Show. The automaker is understandably keen to draw inspiration from its classic Quattro line of automobiles, specifically the original Ur-Quattro from 1980 and the short-wheelbase Sport Quattro that took part in rally racing and set a record at the Pikes Peak Hill Climb in 1987. A massive dose of modernity comes courtesy of its 700-horsepower plug-in hybrid powertrain.
There is a clear link in the styling of the Sport Quattro Concept to Quattro coupes of the past, from the large flat surfaces that make up its C pillars to the blisters over the fenders and the basic headlamp shape (equipped as they are with Audi's Matrix LED technology). Pay special attention to the car's grille, which introduces a slightly new design language that is expected to be seen in the next generation of Audi's mainstream production models.
The interior of the Sport Quattro Concept is a refreshing departure from Audi's admittedly attractive and useable design, with sharp lines and lots of visible carbon fiber. There are seats for four occupants inside, along with a comparatively generous cargo area measuring 10.59 cubic feet.

VW stripped of Green Car Of The Year awards for Jetta, A3 diesels

In the wake of the ongoing VW diesel scandal, Green Car Journal has announced it will rescind the two Green Car Of The Year awards that the Volkswagen Group won with diesel vehicles that have been since been proven to not meet the stated emissions levels. The two vehicles are the 2009 VW Jetta TDI, which won in 2008, and the 2010 Audi A3 TDI, which won in 2010. Green Car Journal (GCJ) did not say if it would retroactively name any replacement winners. This is the first time in the history of the Green Car Of The Year Awards that the honor has been taken away from the winner. In a statement announcing the change, GCJ publisher Ron Cogan wrote that, "this award rescission should not cast a negative light on advanced diesel technology in general. Many diesel models from a variety of auto manufacturers meet EPA and CARB emissions standards, bringing with them higher fuel efficiency, decreased petroleum use, and lower carbon emissions – all important environmental goals." VW AND AUDI RETURNING GREEN CAR OF THE YEAR® AWARDS, VEHICLES DEEMED INELIGIBLE SAN LUIS OBISPO, Calif., Sept. 30, 2015 – Green Car Journal is rescinding the Green Car of the Year® awards previously honoring the 2009 VW Jetta TDI and 2010 Audi A3 TDI, the first time this has occurred in the award program's decade-long history. Audi of America President Scott Keogh has informed Green Car Journal that Audi will return its 2010 Green Car of the Year® award in the wake of Volkswagen Group's admission that it deliberately deceived government authorities about emissions from the Audi A3 TDI. Volkswagen of America has also informed Green Car Journal it will return its 2009 Green Car of the Year® award for the VW Jetta TDI. "Rescinding the Green Car of the Year® awards for the VW Jetta TDI and Audi A3 TDI is unfortunate but appropriate," said Ron Cogan, editor and publisher of the Green Car Journal and CarsOfChange.com. "These models were selected as Green Car of the Year® above others for compelling reasons, including high fuel efficiency, reduced carbon emissions, a fun-to-drive nature, and the ability to meet 50 state emissions requirements with advanced diesel technology." However, VW Group has now admitted that its software programming intentionally caused in-lab emissions testing to read significantly lower nitrogen oxide emissions than these vehicles actually produced on the road.

Audi 3D-printed this tiny Type C racer, we want to drive it

See this little guy? No, not the one driving – that's Professor Hubert Waltl, Audi's head of production and Volkswagen's chief toolmaker. The thing he's driving, though, is a 1:2 scale replica of the 1936 Auto Union Type C. And it was 3D-printed entirely in house. Not in one piece, mind you. It's too big for that. But the Audi Toolmaking division employed metal printing technology to fabricate all the parts that went into this replica of one of the most dominant of the Silver Arrow grand prix racers of the pre-war era. It's essentially like the pedal car Audi rolled out nine years ago, or the E-Tron concept it showed us nearly five years ago. Only this one uses more advanced manufacturing techniques. Aside from making us want to drive it like nobody's business, the half-sized vehicle serves to showcase the advancements which Audi and the VW Group are making in manufacturing – particularly in the area of 3D printing. The German automaker presently has the technology to print laser-melted layers of metallic powder – either steel or aluminum – with grains measuring half the diameter of a human hair. The equipment can handle objects as large as 7.9 inches high by 9.5 inches wide – which, as small as this little car looks, is still a bit too large to simply print out in one piece. Audi Toolmaking prints "Auto Union Typ C" - Exact model of the "Silver Arrow" from a 3D printer - Audi Board of Management Member for Production Prof. Dr. Hubert Waltl: "This underscores our pioneering role in toolmaking." From powder to a component: With a 3D printer, Audi Toolmaking has produced a model of the historical Grand Prix sports car "Auto Union Typ C" from the year 1936. The company is now examining further possible applications of metal printers for the production of complex components. At the same time, Audi is creating important synergies with toolmaking in other parts of the Volkswagen Group. "We are pushing forward with new manufacturing technologies at Audi Toolmaking and at the Volkswagen Group," stated Prof. Dr. Hubert Waltl, Audi's Board of Management Member for Production and Head of Toolmaking at the Volkswagen Group. "Together with partners in the area of research, we are constantly exploring the boundaries of new processes. One of our goals is to apply metal printers in series production." The Volkswagen Group has a total of 14 toolmaking units in nine countries. Under the leadership of Prof. Dr.