1952 Dodge Coronet 2 Door on 2040-cars

Auto blog

Dodge Challenger spied exercising supercharged Hellcat Hemi V8

One of the prime complaints against the Dodge Challenger is that, even in SRT8 guise, its 470 horsepower is responsible for hauling over 4,200 pounds of vehicle. For comparison, the 420 hp in the Ford Mustang GT only has to deal with 3,618 lbs. Things only get worse from there, as the higher-performance variants of both the Mustang and the Chevrolet Camaro are far more powerful than an SRT8 without adding on much heft.
So what is Chrysler to do? The correct answer is add a whole lot more grunt to its hefty two-door and even the odds. That's where the all-new Hellcat engine comes into play. We reported on this engine in May, and suggested that the Hellcat, a supercharged powerplant based on a 6.4-liter V8, would easily generate 500 to 570 hp and could likely arrive boasting more than 600 ponies.
Chrysler's ace in its sleeve has now been spied testing, with a number of Hellcat-equipped Challengers running the potent new engine both in more urbanized areas and under the sun of Death Valley. The hoods on these testers have been raised to accommodate the engine, and that camouflage over the fascias of these prototypes is there to hide a larger air intake. We also note what appears to be a new split grille under wraps. As for power output, our spies are now suggesting a Viper-equalling 640 hp from the Hellcat-equipped cars.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Jeep Grand Cherokee, Dodge Durango still catching fire after recall

Automakers issue recalls all the time. It's part of the cost of doing business. We just assume that once the recall has been carried out, the problem in question has been fixed. But that's not always the case, as this latest investigation being undertaken by the National Highway Traffic Safety Administration goes to show. The problem stems back to a recall issued by Chrysler last summer. It revolved rather the sun visor in the SUVs it makes at its Jefferson North Assembly Plant – specifically, the screw affixing the sun visor could end up rubbing against the wiring for the lamp in the vanity mirror, potentially causing an electrical short and even a fire. 62 such short circuits, 38 fires and three injuries reported, prompting Chrysler to recall nearly 900,000 units of the 2011-2014 Jeep Grand Cherokee and Dodge Durango (over 650,000 of them in the United States). The plastic spacers they installed to rectify the problem, however, may not have done the trick. Eight reports (but none involving injuries) have been filed with the NHTSA regarding the same issue recurring, spurring the government agency to open a new investigation into the matter. If deemed necessary, the NHTSA could ask FCA to issue another recall to fix the issue again, which we may necessitate the installation of a fuze to prevent any such the electric short. Related Video: INVESTIGATION Subject : Headliner Fires Date Investigation Opened: MAY 01, 2015 Date Investigation Closed: Open NHTSA Action Number: RQ15003 Component(s): ELECTRICAL SYSTEM , INTERIOR LIGHTING Manufacturer: Chrysler (FCA US LLC) SUMMARY: On July 1st, 2014 Chrysler (FCA US LLC) issued safety recall 14V-391 to remedy a wiring-related fire hazard on the headliner of approximately 661,888 model year (MY) 2011-2014 Jeep Grand Cherokee and Dodge Durango vehicles manufactured between January 5, 2010 and December 11, 2013. The recall was in response to the Office of Defects Investigation (ODI) investigation EA14-001 during which data provided by Chrysler indicates that the fire is caused by an electrical short in the vanity lamp wiring for either one of the sun visors mounted on the vehicle. The sun visors are mounted to the roof of the vehicle through the headliner with three metal screws.